bela ide won't boot after plugging in bela mini

giuliomoro bela.local in the browser does not work but I am able to get in via ssh after a longer period of time than I am used to.

I am able to run make -C ~/Bela/ PROJECT=looper-oleds run CL="-p16" from the unit via ssh and get my project to run successfully, I just can't access the ide.

it appeared to run successfully:

make -C /root/Bela idestartup idestart
make: Entering directory '/root/Bela'
Enabling the IDE at startup
Starting IDE...done
make: Leaving directory '/root/Bela'

and ifconfig looks right to me?

ifconfig en17
en17: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	options=400<CHANNEL_IO>
	ether be:1a:98:ae:69:50
	inet6 fe80::10d1:6558:4e5d:e84f%en17 prefixlen 64 secured scopeid 0x18
	inet 192.168.7.1 netmask 0xffffff00 broadcast 192.168.7.255
	nd6 options=201<PERFORMNUD,DAD>
	media: autoselect (100baseTX <full-duplex>)
	status: active

but still no dice. I'm running 13.0 (22A380)

still doesn't load. Is port 80 right?

journalctl --boot -fu bela_ide -n 3000

-- Logs begin at Thu 2016-11-03 17:16:43 UTC. --
Mar 17 00:21:21 bela systemd[1]: Started Bela IDE Launcher.
Mar 17 00:21:34 bela node[437]: starting IDE from /root/Bela/
Mar 17 00:21:35 bela node[437]: setting pwd timeout
Mar 17 00:21:35 bela node[437]: listening on port 80

giuliomoro I've tried http://bela.local/ 192.168.7.2 and 192.168.6.2.

here's some new info, I just tried to git clone the c language server while ssh'd and it seems I no longer have access to the internet on the unit:

git clone --depth=1 --recursive https://github.com/MaskRay/ccls
Cloning into 'ccls'...
fatal: unable to access 'https://github.com/MaskRay/ccls/': Could not resolve host: github.com

this is what my /etc/network/interfaces file looks like:

1 # This file describes the network interfaces available on your system
  2 # and how to activate them. For more information, see interfaces(5).
  3
  4 # USB RNDIS gadget (Windows / Linux compatible)
  5 auto usb0
  6 iface usb0 inet dhcp
  7
  8 # iface usb0 inet static
  9 #     address 192.168.6.2
 10 #     netmask 255.255.255.0
 11 #     network 192.168.6.0
 12
 13 #�[m+USB NCM gadget (macOS / Linux compatible)
 14 auto usb1
 15 iface usb1 inet dhcp
 16 # iface usb1 inet static
 17 #     address 192.168.7.2
 18 #     netmask 255.255.255.0
 19 #     network 192.168.7.0
 20
 21 # The loopback network interface
 22 auto lo
 23 iface lo inet loopback
 24
 25 # Ethernet
 26 allow-hotplug eth0
 27 iface eth0 inet dhcp
 28 # Example to keep MAC address between reboots
 29 #hwaddress ether DE:AD:BE:EF:CA:FE
 30
 31 # WiFi Example
 32 allow-hotplug wlan0
 33 iface wlan0 inet dhcp
 34 wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
 35 # The lines above should work if you have a wifi interface called wlan0.
 36 # To see the actual name of your interface, run
 37 #   ip a
 38 # and identify it among the ones listed then replace `wlan0` above with the name of your interface
 39 # To provide credentials to your network, run the following at the command line:
 40 #    wpa_passphrase YourNetworkName YourNetworkPassword >>/etc/wpa_supplicant/wpa_supplicant.conf
 41 # then:
 42 #     ifdown wlan0; ifup wlan0
 43 # where `wlan0` is the name of your interface as found above.
 44

This was working before

I'm also seeing errors when I use some basic terminal commands:

ls

channel 16: open failed: administratively prohibited: open failed
channel 16: open failed: administratively prohibited: open failed

giuliomoro

ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
    link/ether f4:b8:98:ae:69:4c brd ff:ff:ff:ff:ff:ff
3: usb0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether be:1a:98:ae:69:4e brd ff:ff:ff:ff:ff:ff
    inet6 fe80::bc1a:98ff:feae:694e/64 scope link
       valid_lft forever preferred_lft forever
4: usb1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether be:1a:98:ae:69:51 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::bc1a:98ff:feae:6951/64 scope link
       valid_lft forever preferred_lft forever

didn't work. I am noticing that in the internet sharing ilst there are two entries for bela now, maybe because of also plugging in the bela mini at some point?

No luck

If it was just the IDE that wasn't working I'd at least be able to work in vim on-device, but without internet I can't configure a language server or use git